Loading...
> >

dforce lumpy dress skirt? Lully Tadema dress

PitmaticPitmatic Posts: 899
edited May 10 in The Commons

Hi

I appear to to getting a lumpy skirt as per the attached picture any ideas what i am doing wrong? :)

the dress is Lullys Tadema dress https://www.daz3d.com/dforce-tadema-dress-for-g8f

I have tried deleting the dress and reloading it but the lumps remain. 

 

 

 

 

 

 

 

Untitled-2.png
414 x 689 - 399K
Post edited by Pitmatic on

Comments

  • Richard HaseltineRichard Haseltine Posts: 100,960

    I am not seeing that. Are you sure there is only one copy of the dress? Which materials are you using?

  • PitmaticPitmatic Posts: 899

    I am using the default materials with the dress, the figure is Van helsing and the dforce simulation is current frame as its a simple standing pose

  • PitmaticPitmatic Posts: 899

    One copy of the dress

     

  • FirstBastionFirstBastion Posts: 7,762

    Can you switch from texture mode to hidden line wire-mesh and take a screen snap?  And is there any kind of displacement map or strong bump map being used in the surfaces tab.

  • Richard HaseltineRichard Haseltine Posts: 100,960

    So this has been converted to Genesis 9? Do you get the same issue with Genesis 8?

  • PitmaticPitmatic Posts: 899
    edited May 10

    So this the gen 9 figure with the lumps

    this is gen 8 with the lumps

     

    this is gen 8 with a fabric factory shader

     

     

    and this is the wireframe

     

    I have done several scenes with gen 9 in this dress and no lumps but in this scene the lighting is from above and is showing them up I think now i got annoyed lol and set smothing to max and that did remove the lumps but should not be required I would have thought maybe?

     

     

    Untitled-2.png
    414 x 689 - 399K
    Untitled-3.png
    270 x 470 - 221K
    Untitled-4.png
    350 x 548 - 391K
    Untitled-5.png
    280 x 477 - 270K
    Post edited by Pitmatic on
  • felisfelis Posts: 4,340

    Does it look lumpy before simulation?

  • PitmaticPitmatic Posts: 899
    edited May 10

    Not really there are the odd shapes you get in dforce cothes when they try to follow the body pose before simulation, but this only shows with the overhead lighting in other outdoor scenes it seems fine or at least its not noticable in more filling light

     

    Post edited by Pitmatic on
  • Faeryl WomynFaeryl Womyn Posts: 3,628

    That is a strange looking mesh to me, why is it not all straight lines up and down as well as straigh across. It looks messy and can be what's causing your problem.

  • ZippyGuitarZippyGuitar Posts: 845
    edited May 11

    Faeryl Womyn said:

    That is a strange looking mesh to me, why is it not all straight lines up and down as well as straigh across. It looks messy and can be what's causing your problem.

    It's originally made in Marvelous Designer. I would be very surprised if the mesh is what's causing the issue. I have used the Tadema Dress quite a bit over the years (it was released in 2018) and have never ran into this issue.

    @Pitmatic , is the dress by chance in Base Resolution or is it in High Resolution?

    Post edited by ZippyGuitar on
  • ZippyGuitarZippyGuitar Posts: 845
    edited May 11

    Hmm, So I have to eat my own words. I have NO issues with the dress and lumpiness UNLESS I use bright spotlights above the character although they are not near as bad as what Pitmatic has shown. I set the dress to High Resolution and Subdivision set to 2 with smoothing on. I can see a few faint lumpy areas just nothing extreme. Never have I ever noticed this before. 

    EDIT: I just did some more tests on this. I am just astounded I have never noticed this before. I have set Subdivision to 3, Smoothing to Base Shape and Generic, Smoothing Iterations from 2 to 5 and adjusted dForce settings on the dress several times. I have the worst results using the supplied Shaders/Materials by Lully. I also have 3DArena's expansion and I see no lumpiness at all. 3D Arena uses normal maps instead of Bump maps so maybe that's why I had never seen the lumpiness before. All of the Tadema dresses I have saved in my character subsets have normal maps in the Shaders.

    Post edited by ZippyGuitar on
  • richardandtracyrichardandtracy Posts: 5,683
    I noticed from the images that some of the lumps coincide with triangular facets. These tend to be a bit stiffer in simulations and smoothing. Wonder if that has anything to do with it? Regards, Richard
  • PitmaticPitmatic Posts: 899

    @ZippyGuitar the dress is in high resolution rendersub 2 the lighting is a 4 x 4 m emissive plane at some distance above I was trying to get some alma tadema style lighting going in my temple scene :)

    I cant get the lumps to go away or the annoying dforce crease that sometimes appears so i will just photoshop them out not ideal as i am lazy :) 

    Where are the 3DArena textures are they historical?

     

  • ZippyGuitarZippyGuitar Posts: 845
    https://www.daz3d.com/epic-dforce-tadema-dress-for-g8f
  • PitmaticPitmatic Posts: 899

    Thank you ZippyGuitar

  • LullyLully Posts: 25

    Wowza! not seen it like that before by me or in the galleries by others.
    I have been playing around with the dforce settings and also the properties of the dress, this may help.
    Reduce the stretching and up the stretch dampening - see zip attached for the Mat file/thumb (just plop it into your dforce surfaces folder, this will only affect the skirt parts.
    Also, after simulation change the following:
    Change SubD type from Catmark to Catmull-Clark (Legacy)
    Change smoothing type from Base shape match to Generic

     

    zip
    zip
    TademaSkirt.zip
    19K
  • ZippyGuitarZippyGuitar Posts: 845

    @Lully Thank you very much for all that info. I never thought of changing the SubD type even though I have done so with other items before. 

  • PitmaticPitmatic Posts: 899

    Thank you @Lully i will gives this a go. :)

Sign In or Register to comment.